Ships nationwide from Rock Hill, SC · Local service across the Carolinas
Mon-Fri 7:00-5:00 · 803-981-3651
PiedmontIndustrial SalesCartCall for a quote
G4, 5 HP Rotary Screw Air Compressor with Dryer, 53 gal air tank, 230/1/60, 145 PSIG4, 5 HP Rotary Screw Air Compressor with Dryer, 53 gal air tank, 230/1/60, 145 PSI, view 2G4, 5 HP Rotary Screw Air Compressor with Dryer, 53 gal air tank, 230/1/60, 145 PSI, view 3

Asset: Atlas Copco

Atlas Copco
8152103849

G4, 5 HP Rotary Screw Air Compressor with Dryer, 53 gal air tank, 230/1/60, 145 PSI

$10,166
Call to order: 803-981-3651

Straight answers on sizing, phase, and freight: five minutes on the phone, no runaround.

Covered by the manufacturer's written warranty, not a warranty of ours. For a free copy before you buy, call 803-981-3651.

5
HP
18
CFM
141
Max PSI
  • 5 HP
  • 18 CFM
  • 53-gal tank
  • 141 PSI max

About this product

Description supplied by the manufacturer. Any claim or guarantee in it is the manufacturer's to honor, and we will help you contact them.

The Atlas Copco G4 FF (8152103849) is a tank-mounted, oil-injected rotary screw air compressor with a built-in refrigerant dryer, built for professional workshops that need a steady supply of clean, dry compressed air. In an oil-injected screw compressor, two intermeshing rotors (the screw element) compress the air while a small amount of oil seals, cools, and lubricates them, and that oil is separated out again before the air leaves the machine. Mounting the whole package on its own air receiver, the storage tank, gives you a compact, self-contained unit that needs only a power connection and an air outlet to start working.

The FF, or Full Feature, designation means an integrated refrigerant dryer is fitted. This dryer chills the compressed air so that water vapor condenses out and drains away, leaving the air reaching your tools dry rather than damp, which matters for spray painting, pneumatic tools, and any process sensitive to moisture. Oil carry-over is kept low, with a typical oil content of around 5 mg/m³ in the delivered air.

The unit delivers about 18 cfm (8.5 l/s) of free air at 138 psi (9.5 bar), driven by a 5 hp (4 kW) IE3 motor. IE3 is an international efficiency class, meaning the motor uses less energy for the same work. To size the compressor, compare that 18 cfm output against the combined air demand of the tools it will feed, adding up each tool's requirement and leaving some headroom for future additions. It runs at a low 62 dB(A), quiet enough to sit within a working shop.

Power is single-phase 230 V, 60 Hz, through a direct-on-line starter, meaning the motor is connected straight to the supply as it starts, so confirm your electrical supply and circuit protection can handle the start-up current before installation. An Elektronikon Basic microprocessor controller manages running and protection, with remote monitoring available through AIRKeeper.

Performance is rated for ambient temperatures from about 34 °F to 115 °F (1 °C to 46 °C), and output derates above roughly 3,300 feet (1,000 meters) of altitude, so allow for that at high-elevation sites. The system holds about 0.66 US gallons (2.5 liters) of Roto Synthetic Xtend Duty fluid, the synthetic compressor oil specified for this machine; using the correct genuine Atlas Copco oil and filters at the recommended service intervals keeps it performing to its original specification. It is air-cooled and needs adequate ventilation and clearance for the cooling airflow, and the compact package stands about 50 in (1,260 mm) high. Made in Italy.

As a complete oil-injected screw unit under 20 hp (15 kW), fixed speed and full feature, it arrives ready to connect and matched to specification throughout.

Features

  • Oil Injected Screw Compressor, Air Cooled
  • Tank Mounted
  • Capacity: 18 CFM @ 138 PSI
  • Motor: 5HP, IE3 TEFC Motor
  • Voltage: 230V/1ph/60Hz
  • 145 PSI Maximum Operating Pressure
  • Microprocessor Control: Electronikon Basic
  • Remote control/monitoringVia AIRKeeper
  • Long Life RDX (Roto Extend) Synthetic Oil
  • Full Feature Model: Integrated refrigerant dryer
  • Footprint: 57"L x 24"W x 50"H

Full specifications

18 specs
HP5
CFM18
Phase1
FamilyG 4 FF TM 200 CAI (2021)
SeriesG2-7
ControlBasic control
CoolingAir cooled
Max PSI141
Voltage230 V
MountingTank Mounted
Frequency60 Hz
Tank Size53
ControllerNano
Each Weight474 LBS
Noise Level62 dB(A)
Product TypeRotary Screw Air Compressor
Integrated DryerYes
Dimensions (L x W x H)56.3 x 26.18 x 49.61 in

More rotary screw compressors

Not seeing the size you need?

The full book is longer than this page. Call: if your shop needs it, it's a phone call away from your dock.

Call 803-981-3651Fleet & export quotes