Ships nationwide from Rock Hill, SC · Local service across the Carolinas
Mon-Fri 7:00-5:00 · 803-981-3651
PiedmontIndustrial SalesCartCall for a quote
GA18 VSDS, 25 HP Premium Rotary Screw Air Compressor with Dryer, tankless, 460/3/60, 175 PSIGA18 VSDS, 25 HP Premium Rotary Screw Air Compressor with Dryer, tankless, 460/3/60, 175 PSI, view 2GA18 VSDS, 25 HP Premium Rotary Screw Air Compressor with Dryer, tankless, 460/3/60, 175 PSI, view 3

Asset: Atlas Copco

Atlas Copco
8153348176

GA18 VSDS, 25 HP Premium Rotary Screw Air Compressor with Dryer, tankless, 460/3/60, 175 PSI

$32,928
Call to order: 803-981-3651

Straight answers on sizing, phase, and freight: five minutes on the phone, no runaround.

Covered by the manufacturer's written warranty, not a warranty of ours. For a free copy before you buy, call 803-981-3651.

25
HP
138
CFM
185
Max PSI
  • 25 HP
  • 138 CFM
  • 185 PSI max

About this product

Description supplied by the manufacturer. Any claim or guarantee in it is the manufacturer's to honor, and we will help you contact them.

The Atlas Copco GA18 VSDs FF (8153348176) is a variable speed drive, oil-injected screw air compressor built for a steady industrial compressed air supply and wired for a 460 V three-phase 60 Hz feed. Oil-injected means a controlled flow of oil seals, cools, and lubricates the rotating screw element as it compresses the air, which is what lets the unit run continuously at a stable discharge pressure. The FF designation stands for Full Feature, meaning an air dryer is built into the same enclosure so the machine delivers clean, dry air ready to pipe straight to your tools and processes.

Being a variable speed drive (VSD) machine, its motor speeds up and slows down to track your actual air demand instead of running at full speed and unloading. In plants where demand rises and falls through the day, that draws only the power the moment requires and typically cuts energy use substantially compared with a fixed-speed compressor. It delivers up to 138 cfm (65.2 l/s) of free air at 102 psi (7 bar), and its working-pressure range runs from a minimum of 58 psi (4 bar) up to a maximum of 186 psi (12.8 bar).

The integrated ID65+ dryer removes moisture from the compressed air and drains the condensate, the liquid water that collects, automatically so it does not travel downstream to rust piping or upset pneumatic equipment, bringing the compressed air down to about 37°F (3°C) at the outlet; typical oil carry-over in the delivered air is around 3 mg/m³. The compressor is floor mounted rather than sitting on an air receiver, so if your system needs buffer storage you would pair it with a separate air tank sized to your usage.

With that flow and an on-board dryer, this unit suits workshops and production lines needing a dependable clean-air supply in the mid-range flow band, and its compact footprint, roughly 28 inches (700 mm) wide, lets it stand close to the point of use. It is air cooled and holds around 3.2 US gallons (12 liters) of Roto Duty Extend (RDX) synthetic compressor oil.

Operation is handled by the Elektronikon Touch controller, a touchscreen microprocessor control that monitors the machine and lets you set the target pressure. The GA18 VSDs FF is a genuine Atlas Copco unit, built in Italy, and is rated for ambient inlet air up to 115°F (46°C) and for installation up to 3,281 feet (1000 m) above sea level before its output derates; it is the standard-ambient build rather than a high-ambient version, so keep that ceiling in mind if your compressor room tends to run warm.

Two site details decide how smoothly this one installs. Second is condensate routing, since the machine has both an automatic and a manual drain connection and each needs somewhere to discharge, so work that into the layout before the unit is set in place and piped up.

Features

  • Oil Injected Screw Compressor, Air Cooled
  • Capacity: 138 CFM @ 102 PSI
  • Motor: 25HP, FASR motor and Neos Next Drive
  • Voltage: 460V/3ph/60Hz
  • 185 PSI Maximum Operating Pressure
  • Advanced Microprocessor Control: Elektronikon Touch
  • Long Life RDX (Roto Duty Extend) Synthetic Oil
  • FF unit: Integrated dryer included
  • Footprint: 43"H x 28"W x 59"L

Full specifications

13 specs
HP25
CFM138
Phase3
FamilyGA 18 VSDs FF API (2022)
SeriesGA5-18 VSDs
ControlMK5 Touch No IO
CoolingAir cooled
Max PSI185
Voltage460 V
Frequency60 Hz
Each Weight1302.93 LBS
Product TypeRotary Screw Air Compressor
Integrated DryerYes

More rotary screw compressors

Not seeing the size you need?

The full book is longer than this page. Call: if your shop needs it, it's a phone call away from your dock.

Call 803-981-3651Fleet & export quotes